7th Cavalry Brigade in 6mm for the 100 Days Campaign

The next unit I completed for my growing 6mm Napoleonic project was the British 7th Cavalry Brigade. I made use of the Light Dragoons and Hussars that are provided in the Baccus blister pack I bought at The Joy of Six.
The 7th Cavalry Brigade was made up of 3rd (KGL) Hussar Regiment and the 13th Light Dragoon Regiment, so these figures were perfect.


The lines are slightly skewed to give an impression of movement.



You may be wondering where I am getting my research from for these units, initially it is based on the cards that came with the 100 Days Campaign set, but I am using two main websites for filling in the details.

First of all this impressive OOB for the Waterloo campaign has helped enormously in the details of Regiments etc. On the other hand, I was guided by a chum to this French website which details all the uniforms of all the units involved in the 100 Days. Despite it being in French (my French is at a schoolboy level...) this last one has been a lifesaver as I haven't had to invest in a library of tomes detailing the correct shade of Bricoles. 

Finally, below I have detailed how I go about basing these units. The cavalry in particular have been tricky and I had to think about how best to create the basing for two lines of tiny horses... I hope this helps anyone else trying out in the big world of 6mm.

The first stage is to superglue the front line in position (you could do the rear line first, either works). You'll notice that I have already painted the base in Intermediate Green, this is just in case I miss some spots in future stages.


Then, very carefully, using a cocktail stick I gently ease Pollyfilla into the gaps between the horses and cover the front half of the base. Taking a steel ruler I square up the back end of the Pollyfilla whilst it is still wet.


Next stage is to take some PVA glue and brush it very carefully onto the Pollyfilla once it has dried (usually 24hrs). I then dip the base into a plastic Chinese take-away tub filled with silver sand. I use this sand for 6mm as it is very fine but still creates a texture on the base.


Again, leaving this to dry for a few hours, I water down some Intermediate Green and apply it with a brush. I have found that if this paint is watered down enough it actually spreads out across the sand and means it is easy to apply.


Once the paint is dry, I inkwash the base in Flat Earth, watered down so it fills in around the sand.


When the inkwash is dry I gently drybrush the entire base in Yellow (I use a bog standard acrylic paint I once picked up in an art shop).


Then I superglue the rear row into position, the closeness of the two lines shows how hard it would be to get the Pollyfilla in between all the ranks.


Using the cocktail stick again (the longer the better), I do the same as before and ease the Pollyfilla into place around the rear ranks.


However, when this is dry I clean up the rear line where some of the Pollyfilla has spilt over onto the area of the label. I just sand this excess plaster off.


Then I follow the same steps with the sand, paint, inkwash and drybrush as before to blend the front and rear sections together. The rear strip where the label will go is painted Black and I spray Matt Varnish on the entire base.


The final stage is to add grass tufts to the base and patches of Woodland Scenics static grass to break up the shape of the base. And there you have it, it probably takes about two to three days to complete with drying times, but as each stage only about ten minutes they can be done whilst you are getting on with other projects and painting. 

I hope this was of help!

Comments

  1. Your bases are very nice, but very labour intensive. Can I suggest you try Basetex from Colour Party Paints, also available from Irregular Miniatures. Being a Green coloured sand the stuff works really well.
    Check my blog, re how Ive done my Blucher bases.
    independentwargamesgroup.
    Thanks Robbie.

    ReplyDelete
    Replies
    1. Thanks Robbie, your blog is excellent and I have started following it. I will have a look at the Basetex stuff, but I wonder if it is not very expensive compared to my basing? Your bases look amazing though!

      Delete
  2. Hmm I must admit i made a mistake with my Blucher bases. I use 80X60 magnet covered base and the troops and the card with the details are metallic based it saved me rebasing which is fine but I decided because the depth mutiple was 20 and 40 I made the detail piece 20mm wide. That was the mistake. I'm now seriously considering reducing the strip to 8mm wide and use the small die frame from mini-bits. I can cover the reduction in the detail strip by adding a based strip at the front .
    As for basing I use a different method to both of you . Once the figures are stuck on the base I apply pvc glue and cover it in lava sand. That gets painted brown and dry brushed in a tan colour finished off by scattered patches of flock. Looks ok and matches my table at home. You can see them and my reasoning here http://flownlegions.blogspot.com.es/2015/07/blucher-basing-final-decision.html

    ReplyDelete
  3. Oh sorry I got carried away there . Love the bases. I wish I had started from scratch so I could have used those sally4th bases All the figures you have posted so far have been excellent.

    Bob

    ReplyDelete
    Replies
    1. Ha ha, don't worry, please do get carried away! Thanks, your bases look great and I toyed with the idea of using magnets so I could attach artillery and the like. The Sally 4th Bases are are great bonus for this project. I really like them.

      Delete
  4. Great looking formation. 6mm has so many advantages.

    ReplyDelete
    Replies
    1. Thanks you, yes, it really does for Napoleonics!

      Delete

Post a Comment